Painted waterfall vanity8/6/2023 ![]() ![]() Make sure you are getting the whole item including the sides and even insides of pieces of furniture if you plan to paint there as well.Īfter sanding, use a handheld vacuum or your tack cloth to clean up any dust particles that have settled around your work area. You should use a tack cloth to remove dust particles periodically. Avoid sanding it so hard that you move through the veneer to the underlying construction. While sanding is often seen as burdensome, it will really improve the quality of your work.įor this project, use 220-grit sandpaper to sand the veneer finish, being careful to use only light pressure. Make sure the veneer item in question has been thoroughly cleaned and dried before you move on to the next steps.Īfter your veneer surface has been thoroughly cleaned and dried completely, it is time to sand. If you have a particularly dirty veneer surface, you may need to do this more than once. Rinse the surface and let it dry completely when you're done. Instead, wet a clean cloth with the cleaning solution, wring it out, and then wipe the surface to remove any built-up grease and dirt. It's best to avoid soaking the item, however, as the underlying construction may be damaged by too much. In this case, dirt, dust, and grime can cling to a veneer surface and interfere with your efforts to give it a new look.Ĭlean the surface of the item you're planning to paint with a solution of mild dishwashing liquid and warm water. Like with any project, make sure you take some time to clean early on. Some colors and painting choices may even make the chips more obvious than they were before so make sure to spend a little time before painting on this step. If they have a giant crack or chip in them, however, it won't look any better than it did before painting. The point of painting items is to breathe new life into them and save some money over the cost of replacing said items. This is necessary in order to make your final product look its best. If the veneer is missing sections or has become cracked, carefully remove the damaged section or sections and glue a replacement piece of veneer in its place.Īfter doing this, wait until the wood glue has dried completely before moving on to the next step.ĭo not skip this step. If part of the veneer has begun to pull away from the underlying surface, use wood glue to set it back in place. Repair such problems to ensure that the paint will adhere properly. Veneer, which is a thin layer of decorative wood, can crack, chip, or pull away from the item you want to paint. Since it is not wood all the way through, however, it is cheaper than something that is 100% wood making it an ideal material for many.īefore starting to paint your veneer finished item, you will need to take time to assess the item and repair any damage so that it is in great shape. Since veneer is real wood, many people like its appearance. It is also used in some types of flooring and panels. For durability, we finished off this waterfall dresser makeover with two coats of polycrylic spray.Veneer can be used for a variety of things including, most often, cabinets and furniture. The pretty goldish tone really pops against the white. We cleaned up the metal pulls and were able to use them again. Luckily, these popped off easily from the metal pulls. My sister didn’t like the bakelite bits on the original hardware. You can read more about the process we use to achieve a near perfect finish here. Even with our trusty Zinsser primer, it took 3 coats to get the coverage we wanted. To keep the piece light and fresh we opted for Benjamin Moore’s cloud white paint for the body and drawers of this waterfall dresser makeover. We decided it would never quite match the stain of the veneer and we’d paint it instead. As expected, the bottom piece which was not veneer but solid wood, took the stain very differently from the veneer. We applied a dark espresso stain with a foam brush to all three areas. Since the veneer on waterfall dressers is often thin, we were careful not to sand down to the layer below. We carefully sanded down the wood veneer on the top, the inlay design on the top drawer and the bottom decorative piece. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |